# Details on the Outline

**URL:** <https://forum.grid.space/t/details-on-the-outline/568>\
**Category:** CAM\
**Created:** [February 2, 2022, 2:06pm UTC](https://forum.grid.space/t/details-on-the-outline/568 "2022-02-02T14:06:32Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![enhydra](https://forum.grid.space/user_avatar/forum.grid.space/enhydra/32/1000_2.png) [@enhydra](https://forum.grid.space/u/enhydra)\
**Post date:** [February 2, 2022, 2:06pm UTC](https://forum.grid.space/t/details-on-the-outline/568/1 "2022-02-02T14:06:32Z")

</div>

![Cylinder_Base](https://forum.grid.space/uploads/default/original/2X/5/50b285f8e7257d4bf0f05b810d1922250a9c2aa2.jpeg)

I tried to process this part. But somehow I was not able to generate reasonable milling paths. The “rough” workhorse did strange things with a detail on the outline. Any advice, which combination of operations should work?

[Cylinder\_Base.kmz](https://forum.grid.space/uploads/short-url/8Z808RUZJVVIDHT8qUX7T4rfcMc.kmz) (401.6 KB)

---

<div class="post-metadata">

**Author:** ![stewart](https://forum.grid.space/user_avatar/forum.grid.space/stewart/32/21_2.png) [@stewart](https://forum.grid.space/u/stewart)\
**Post date:** [February 2, 2022, 2:42pm UTC](https://forum.grid.space/t/details-on-the-outline/568/2 "2022-02-02T14:42:38Z")

</div>

those dashed lines on the outside of the circle should not be there. I know what’s causing them (low poly offsetting artifact) and will look at how to clean them up in the roughing op. it’s present in earlier versions of KM, too.

if I can find a clean solution, it’ll be fixed in tonight’s release.

here is a workspace that attempts to use tracing and outlining to workaround this problem.

[cylinder-alt.kmz](https://forum.grid.space/uploads/short-url/mMN3O2yl4pgE4FvF7HcUVFlrqMM.kmz) (477.0 KB)

---

<div class="post-metadata">

**Author:** ![stewart](https://forum.grid.space/user_avatar/forum.grid.space/stewart/32/21_2.png) [@stewart](https://forum.grid.space/u/stewart)\
**Post date:** [February 2, 2022, 2:50pm UTC](https://forum.grid.space/t/details-on-the-outline/568/3 "2022-02-02T14:50:15Z")

</div>

usually it’s just finding the right test case to expose a flaw. I have fixed this in roughing for tonight’s release.

 ![Screen Shot 2022-02-02 at 9.48.10 AM](https://forum.grid.space/uploads/default/original/2X/d/d4499a21ccec1d0bba64951ab1a595cc32320484.jpeg)

---

<div class="post-metadata">

**Author:** ![enhydra](https://forum.grid.space/user_avatar/forum.grid.space/enhydra/32/1000_2.png) [@enhydra](https://forum.grid.space/u/enhydra)\
**Post date:** [February 2, 2022, 9:54pm UTC](https://forum.grid.space/t/details-on-the-outline/568/4 "2022-02-02T21:54:53Z")

</div>

I’ll test it tomorrow. Thank you for your support. 🙂

> I know what’s causing them (low poly offsetting artifact)

How about increasing the resolution? Would that help too?

---

<div class="post-metadata">

**Author:** ![stewart](https://forum.grid.space/user_avatar/forum.grid.space/stewart/32/21_2.png) [@stewart](https://forum.grid.space/u/stewart)\
**Post date:** [February 2, 2022, 10:15pm UTC](https://forum.grid.space/t/details-on-the-outline/568/5 "2022-02-02T22:15:12Z")

</div>

it may help. but the threshold in the code was too low (0) which means artifacts are almost guaranteed on a circle 😑

I usually push new code around midnight GMT. this will be fixed then.
